Basic Setup¶
After installing FRR, some basic configuration must be completed before it is ready to use.
Daemons Configuration File¶
After a fresh install, starting FRR will do nothing. This is because daemons
must be explicitly enabled by editing a file in your configuration directory.
This file is usually located at /etc/frr/daemons and determines which
daemons are activated when issuing a service start / stop command via init or
systemd. The file initially looks like this:
zebra=no
bgpd=no
ospfd=no
ospf6d=no
ripd=no
ripngd=no
isisd=no
pimd=no
ldpd=no
nhrpd=no
eigrpd=no
babeld=no
sharpd=no
staticd=no
pbrd=no
bfdd=no
fabricd=no
#
# If this option is set the /etc/init.d/frr script automatically loads
# the config via "vtysh -b" when the servers are started.
# Check /etc/pam.d/frr if you intend to use "vtysh"!
#
vtysh_enable=yes
zebra_options=" -s 90000000 --daemon -A 127.0.0.1"
bgpd_options=" --daemon -A 127.0.0.1"
ospfd_options=" --daemon -A 127.0.0.1"
ospf6d_options=" --daemon -A ::1"
ripd_options=" --daemon -A 127.0.0.1"
ripngd_options=" --daemon -A ::1"
isisd_options=" --daemon -A 127.0.0.1"
pimd_options=" --daemon -A 127.0.0.1"
ldpd_options=" --daemon -A 127.0.0.1"
nhrpd_options=" --daemon -A 127.0.0.1"
eigrpd_options=" --daemon -A 127.0.0.1"
babeld_options=" --daemon -A 127.0.0.1"
sharpd_options=" --daemon -A 127.0.0.1"
staticd_options=" --daemon -A 127.0.0.1"
pbrd_options=" --daemon -A 127.0.0.1"
bfdd_options=" --daemon -A 127.0.0.1"
fabricd_options=" --daemon -A 127.0.0.1"
#MAX_FDS=1024
# The list of daemons to watch is automatically generated by the init script.
#watchfrr_options=""
# for debugging purposes, you can specify a "wrap" command to start instead
# of starting the daemon directly, e.g. to use valgrind on ospfd:
# ospfd_wrap="/usr/bin/valgrind"
# or you can use "all_wrap" for all daemons, e.g. to use perf record:
# all_wrap="/usr/bin/perf record --call-graph -"
# the normal daemon command is added to this at the end.
Breaking this file down:
bgpd=yes
To enable a particular daemon, simply change the corresponding 'no' to 'yes'. Subsequent service restarts should start the daemon.
vtysh_enable=yes
As the comment says, this causes VTYSH to apply configuration when starting the daemons. This is useful for a variety of reasons touched on in the VTYSH documentation and should generally be enabled.
MAX_FDS=1024
This allows the operator to control the number of open file descriptors each daemon is allowed to start with. The current assumed value on most operating systems is 1024. If the operator plans to run bgp with several thousands of peers than this is where we would modify FRR to allow this to happen.
zebra_options=" -s 90000000 --daemon -A 127.0.0.1"
bgpd_options=" --daemon -A 127.0.0.1"
...
The next set of lines controls what options are passed to daemons when started
from the service script. Usually daemons will have --daemon and -A
<address> specified in order to daemonize and listen for VTY commands on a
particular address.
The remaining file content regarding watchfrr_options and *_wrap settings should not normally be needed; refer to the comments in case they are.
Services¶
FRR daemons have their own terminal interface or VTY. After installation, it's
a good idea to setup each daemon's port number to connect to them. To do this
add the following entries to /etc/services.
zebrasrv 2600/tcp # zebra service
zebra 2601/tcp # zebra vty
ripd 2602/tcp # RIPd vty
ripngd 2603/tcp # RIPngd vty
ospfd 2604/tcp # OSPFd vty
bgpd 2605/tcp # BGPd vty
ospf6d 2606/tcp # OSPF6d vty
ospfapi 2607/tcp # ospfapi
isisd 2608/tcp # ISISd vty
babeld 2609/tcp # BABELd vty
nhrpd 2610/tcp # nhrpd vty
pimd 2611/tcp # PIMd vty
ldpd 2612/tcp # LDPd vty
eigprd 2613/tcp # EIGRPd vty
bfdd 2617/tcp # bfdd vty
fabricd 2618/tcp # fabricd vty
vrrpd 2619/tcp # vrrpd vty
If you use a FreeBSD newer than 2.2.8, the above entries are already added to
/etc/services so there is no need to add it. If you specify a port
number when starting the daemon, these entries may not be needed.
You may need to make changes to the config files in /etc/frr.
Systemd¶
Although not installed when installing from source, FRR provides a service file
for use with systemd. It is located in tools/frr.service in the Git
repository. If systemctl status frr.service indicates that the FRR service
is not found, copy the service file from the Git repository into your preferred
location. A good place is usually /etc/systemd/system/.
After issuing a systemctl daemon-reload, you should be able to start the
FRR service via systemctl start frr. If this fails, or no daemons are
started. check the journalctl logs for an indication of what went wrong.
Operations¶
This section covers a few common operational tasks and how to perform them.
Restarting¶
Restarting kills all running FRR daemons and starts them again. Any unsaved configuration will be lost.
service frr restart
Note
Alternatively, you can invoke the init script directly:
/etc/init.d/frr restart
Or, if using systemd:
systemctl restart frr
Reloading¶
Reloading applies the differential between on-disk configuration and the current effective configuration of running FRR processes. This includes starting daemons that were previously stopped and any changes made to individual or unified daemon configuration files.
service frr reload
Note
Alternatively, you can invoke the init script directly:
/etc/init.d/frr reload
Or, if using systemd:
systemctl reload frr
Starting a new daemon¶
Suppose bgpd and zebra are running, and you wish to start pimd. In
/etc/frr/daemons make the following change:
- pimd=no
+ pimd=yes
Then perform a reload.
Currently there is no way to stop or restart an individual daemon. This is
because FRR's monitoring program cannot currently distinguish between a crashed
/ killed daemon versus one that has been intentionally stopped or restarted.
The closest that can be achieved is to remove all configuration for the daemon,
and set its line in /etc/frr/daemons to =no. Once this is done, the
daemon will be stopped the next time FRR is restarted.